Manx SA7x Installationsanleitung Seite 71
- Seite / 320
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
3.17 Placing the Add-On Storage Element into the Cabinet
3.17 Placing the Add-On Storage Element into the Cabinet
The add-on storage element and the DECArray300 cabinet system hardware
should be ready for installation. See Figure 3–10 while performing the
installation procedure.
1. Turn the storage element so the side grooves are facing toward the cabinet
guide rails. (The storage element may look upside down at this point; this
will be rectified when the OCP is reinstalled to correspond with the disk or
tape drive orientation.)
2. Use the mounting brackets, part number 74–44414–01, for mounting
Storage Elements into the Sx300 Cabinet. These mounting brackets are
enclosed to the cabinet. The mounting holes in the brackets are adjustable
(long holes).
3. Push the bracket towards the front for DSSI storage elements prior to
tightening the mounting screws to fix the brackets to the storage enclosure.
4. Push the bracket towards the rear for SDI storage elements prior to
tightening the mounting screws to fix the brackets to the storage enclosure.
5. Lift and move the storage element into place using a Digital lifting device
(part number FC–10117–AC), and the following procedure:
CAUTION
If a lifting device is not available, two people are needed to install
the disk or tape drive into the cabinet. The disk or tape drive must
be handled with care. Manual installation is not recommended. See
Table 3–4 for all single storage element weight you can install in the
DECArray300 3 high cabinet.
a. Place the lifting device in an upright position with the lift platform
facing away from the operator.
b. Make sure sufficient open space for extending the lift platform.
c. Support the top of the lifting device with one hand. With the other
hand, raise the lift platform holding latch from the cross bar to release
it.
d. Lower the lift platform to its service position.
e. Check the hinges at the base of the lift platform to make sure they are
fully extended and locked.
Preparation and Installation 3–29
- Sx300 Storage Array 1
- Installation Guide 1
- Contents 3
- Elements 6
- Configuration 8
- Related Documents 16
- Documentation Conventions 16
- General Information 17
- 1.1 Product Descriptions 18
- 1.2 DECArray300 Specifications 23
- 1.3 Acoustic Noise Values 26
- 1.4 EMC/EMI 27
- 1–12 General Information 28
- General Information 1–13 29
- 1–14 General Information 30
- General Information 1–15 31
- 1.6 Thermal Stabilization 32
- Storage Array 33
- SHIPPING 36
- CXO-688C_S 37
- SHR_X1103_89_SCN 37
- CXO-924A_S 38
- SHR_X1104_89_SCN 38
- CXO-395C_S 39
- SHR_X1105_89_SCN 39
- Preparation and Installation 43
- 3.3 Electrostatic Discharge 48
- 3.5 Mounting the Half Bezel 52
- Figure 3–3 Rear Access Panel 54
- 3.11 Ground Wire 55
- 3.16.1 Chassis Rail Assembly 63
- 3.19 Applying Power 75
- 3.20 Power Controller 75
- 3.23 BUS/OFF/ON Switch (S1) 80
- 6000 System 85
- 4.1.2 Dual-Host Configurations 86
- SHR_X1127A_89 89
- SHR_X1128C_89 96
- SHR_X1128_89 99
- SHR-X0121-90 103
- LABEL AREA 103
- DSSI TERMINATOR 103
- SHR-X0108-90 105
- OPERATOR CONTROL PANEL 106
- 5.1 Steps to Install 108
- 5.1.4 Installation Procedure 116
- SHR-X0124-90 118
- SHR_X1113_89_SCN 121
- SHR-X0126A-90 122
- SHR-X0127A-90 123
- SHR-X0122-90 129
- 5.2.2 Dual-Host Configuration 135
- 5.3 Powering Up the SF7x 149
- 5.4.1 Filling Out the Labels 150
- 5.4.2 Labeling the Cables 150
- 5.4.3 Labeling the OCP 150
- 5.5 Final Verification 152
- 6.1 Steps to Install 154
- 6.1.4 Installation Procedure 160
- CONNECTORS 167
- AC RECEPTACLE 167
- AC POWER 167
- 6.2.2 Dual-Host Configuration 172
- 6.4.1 Filling Out the Labels 176
- 6.4.2 Labeling the Cables 177
- 6.5 Final Verification 179
- SDI Storage Elements 181
- CABINET 183
- 7.3.1 Hardware Check list 184
- 7.3.3 Electrostatic Discharge 188
- Installation Troubleshooting 193
- 2. Remove the Rx7x disk ISE 197
- SHR-X0135A-90 199
- SHR-X0135-90 200
- SHR-X0136A-90 200
- SKID PLATE 201
- 8.2.2 Fault Matrix 205
- 8.2.3 Error Conditions 206
- • Poor power or grounding 207
- 8.2.5 Soft Error Rates 208
- Diagrams 209
- A.1.2 Dual Host Configurations 210
- A.1.3 Stripeset Configurations 211
- A.1 General Cabling Rules 212
- A.2 Cabling Diagrams 213
- A.3 Single-Host Configurations 214
- A.4 Dual-Host Configurations 239
- Enclosure 266
- B.3 Powering Up the ISEs 269
- C.2 Conversion Procedure 276
- C.2.4 Labeling the Cables 283
- C.2.7 Final Verification 291
- SHR_X1128B_89 297
Verwandte Produkte und Handbücher für Elektrische Gehäuse Manx SA7x
Elektrische Gehäuse Manx SA7x Wartungshandbuch
(128 Seiten)
(128 Seiten)
Elektrische Gehäuse Manx SA7x Spezifikationen
(170 Seiten)
(170 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern